GEPRC focuses on the FPV ecosystem, from ready-to-fly quadcopters and cinewhoops to airframes, electronics, motors and navigation accessories. Its product families serve pilots looking for cinematic flying, freestyle performance, long-range exploration or carefully selected parts for custom aircraft.
GEPRC equipment rewards attention to the complete build rather than any single component. A GPS module must match the flight controller’s available connections, a battery must suit the voltage and dimensions of an airframe, and a video or radio configuration must align with the pilot’s existing control and viewing system.
Explore the brand by starting with your flying style and aircraft size. Check receiver protocols, video transmission, mounting, operating voltage and firmware before choosing related parts. That compatibility-first approach makes it easier to build a dependable and purposeful FPV setup.
GEPRC DJI O4 Coaxial Cable
- Exact Model GEPRC DJI O4 Coaxial Cable
- Cable Length 6 cm, 9 cm, 17.5 cm, 20 cm
- Compatibility DJI O4 Air Unit camera-to-air-unit installations
- Connector Type Miniature DJI O4 coaxial connectors at both ends
- Installation Direct replacement; route without twists, crushing or sharp bends
- Package 1 × GEPRC DJI O4 coaxial cable in selected length
GEPRC ELRS 915M/2.4G C3 Gemini Xrossband Receiver
- Exact Model GEPRC ELRS 915M/2.4G C3 Gemini Xrossband Receiver
- RF System ExpressLRS; 915MHz Gemini, 2.4GHz Gemini and 915MHz + 2.4GHz dual-band modes
- Chips & Stability ESP32-C3 with dual LR1121 RF chips and TCXO
- Refresh & Telemetry 25–1000Hz LoRa/FSK refresh; up to 100mW telemetry
- Protocols & Power CRSF, SBUS, SUMD, DJI RS2 Pro and MAVLink outputs; 5V input
- Size & Package 18×23.6×5.7mm, 1.6g; receiver, two dual-band antennas, cable, heat-shrink and manual
- Product Summary Dual-band ExpressLRS receiver with LR1121×2, ESP32-C3, up to 1000Hz refresh and 100mW telemetry.
GEPRC ELRS Nano DUAL 2.4G C3 True Diversity Receiver
- Exact Model GEPRC ELRS Nano DUAL 2.4G C3 True Diversity Receiver
- RF System ExpressLRS 2.4GHz ISM true diversity with two independent RF links
- Chips & Stability ESP32-C3, dual SX1281 RF chips and TCXO
- Refresh & Telemetry 25–1000Hz refresh; 10mW telemetry
- Power & Connectors 5V input; dual IPEX1 antenna connectors; RGB status light
- Size & Package 17×13mm, 1.1g; receiver, two 80mm T-antennas, SH1.0 cable, heat-shrink and manual
- Product Summary Compact 2.4GHz ExpressLRS true-diversity receiver with dual SX1281 RF chains, TCXO and up to 1000Hz refresh.
GEPRC O4 Series Step-Down BEC
- Exact Model GEPRC O4 Series Step-Down BEC
- Compatibility Designed for DJI O4 Air Unit and DJI O4 Air Unit Pro power regulation.
- Input Voltage DC 10.5–25.2V input, compatible with 3–6S batteries; step-down only.
- Output Voltage Default 9V output, switchable to fixed 5V by bridging the 5V pad.
- Control & Wiring Includes EN pad electronic switch control and plug-in cable support.
- Size & Weight Approx. 17 × 8.3mm and 1g.
GEPRC 868MHz/915MHz 2.4G Tri-Band Stick Antenna
- Exact Model GEPRC 868MHz/915MHz 2.4G Tri-Band Stick Antenna
- Frequency Bands 868MHz range 860–870MHz, 915MHz range 900–930MHz and 2.4GHz range 2400–2500MHz.
- Gain & Polarization Linear polarization with 2.8dBi / 2.82dBi / 2.97dBi gain across the three bands.
- RF Performance VSWR ≤1.5 and cross-polarization suppression around −25dB.
- Construction PCB antenna inside low-drag ABS shell with high-quality SMA connector.
- Size & Weight Approx. 172mm long and 11.2g.
GEPRC TAKER F722 45A 32Bit AIO
- Exact Model GEPRC TAKER F722 45A 32Bit AIO
- Processor & Sensors STM32F722 MCU, ICM42688-P SPI gyro, onboard barometer and AT7456E Betaflight OSD.
- ESC & Power Integrated 32-bit 45A ESC, 55A burst for 10 seconds, 2–6S LiPo input and 5V/1A BEC.
- Firmware & Protocols GEPRC_F722_AIO target with DShot600, OneShot and MultiShot support.
- Connectivity Five full UARTs, USB-C, buzzer and LED support, plus dedicated six-pin HD VTX connector.
- Size & Mounting 35 × 33.5mm, 25.5 × 25.5mm mounting and approximately 9.2g.
- Product Summary F722 all-in-one flight controller with ICM42688-P gyro, integrated 32-bit 45A ESC, 2–6S input, 16MB blackbox and direct HD VTX connector.
GEPRC MATEN 5.8G 2.5W VTX PRO (Silver)
- Exact Model GEPRC MATEN 5.8G 2.5W VTX PRO (Silver)
- Power & Modes 25/200/600/1600/2500mW plus Pit mode, with active cooling and thermal protection.
- Frequency & Channels 4884–6184MHz frequency range with 80 channels and direct frequency entry.
- Input & Output DC 7–36V input and 5V/600mA output for camera or cooling fan.
- Control & Audio IRC Tramp OSD control, PAL/NTSC support and built-in microphone for audio transmission.
- Size & Mounting 36.3 × 36.3 × 15.1mm, approx. 20g; 20 × 20mm and 30.5 × 30.5mm M2 mounting, MMCX.
- Product Summary Silver 2.5W analog VTX with 80 channels, 7–36V input, active fan, IRC Tramp, built-in microphone and MMCX antenna interface.
GEPRC MATEN 5.8G 4W VTX PRO
- Exact Model GEPRC MATEN 5.8G 4W VTX PRO
- Power & Modes 25/200/1600/4000mW plus Pit mode, with thermal protection and active fan cooling.
- Frequency & Channels 4800–6200MHz range, 104 channels and direct frequency entry support.
- Input & Camera Output DC 7–36V input for 2–8S; regulated 5V/600mA camera output.
- Control & Connectors IRC Tramp OSD control, SMA antenna connector and SH1.0 6-pin cable.
- Size & Mounting Approx. 53.5 × 29 × 17.2mm, 28.8g; 20 × 20mm M2 mounting pattern.
- Product Summary 4W analog VTX with 104 channels, 4800–6200MHz coverage, 7–36V input, active cooling, thermal protection and IRC Tramp.
GEPRC MATEN 5.8G 3W VTX PRO V2 (SMA)
- Exact Model GEPRC MATEN 5.8G 3W VTX PRO V2 (SMA)
- Power & Modes 25/200/600/1600/3000mW plus Pit mode, with thermal protection and active micro-fan cooling.
- Frequency & Channels 4884–6184MHz coverage with 104 channels and direct frequency entry support.
- Input & Output DC 7–36V input for 2–8S systems with regulated 5V camera output.
- Control & Connectors IRC Tramp OSD control, SH1.0 6-pin cable interface and SMA antenna connector.
- Size & Mounting Approx. 57.5 × 31.5 × 17.5mm, 35.6g; 20 × 20mm and 25.5 × 25.5mm M2 mounting.
- Product Summary High-power 5.8GHz analog VTX with 3000mW maximum output, 104 channels, 7–36V input, active fan cooling, IRC Tramp and SMA connector.
GEPRC WooPower W63 1S Smart Charger
- Exact Model GEPRC WooPower W63 1S Smart Charger
- Charging Performance Six independent channels; up to 3.0A charge current and 0.5A discharge current per channel; up to 78W output.
- Battery Compatibility Supports 1S LiPo, LiHV and LiFe batteries with charge, discharge and storage functions.
- Connectors Built-in PH2.0, BT2.0 and A30 battery interfaces for common whoop packs.
- Input & Display XT60 DC 7–26V and USB-C PD3.0 input; 1.54-inch 240 × 240 IPS display.
- Size & Weight Approx. 125 × 61 × 28mm and 160g; 100W input recommended for full-load operation.
- Product Summary Six-channel 1S smart charger with 3A charging per port, LiPo/LiHV/LiFe support, USB-C PD3.0 and XT60 input, storage mode and a 1.54-inch IPS display.
GEPRC TAKER F405 BLS 65A V2 FC + ESC Stack
- Flight Controller & Gyro: GEP-F405-HD V3 controller with STM32F405 processor and ICM42688-P gyro for supported Betaflight flight-control setups.
- ESC & Current Capability: TAKER H65 BLS 65A 4-in-1 ESC paired with the controller; motor selection must match current and cooling requirements.
- Critical Voltage Limits: ESC input is listed for 3–8S, but the flight controller itself accepts 3–6S; do not feed an 8S battery directly into the FC.
- Connections & Flight Data: USB-C service port, blackbox capability, 5V/9V BEC outputs and interfaces for a compatible DJI video unit and receivers.
- Mounting & Firmware: 30.5 × 30.5mm stack format; verify GEPRCF405 firmware, UART mapping, wiring pinout, capacitors and electrical protection.
GEPRC TAKER F722 BLS 100A 8S FC + ESC Stack
- Flight Controller & Sensor: TAKER STM32F722-based flight controller with ICM42688-P gyro, 16MB onboard blackbox and supported Betaflight firmware target.
- ESC & Motor Drive: High-current 100A continuous 4-in-1 BLS ESC, paired for demanding FPV motors; verify the motor/propeller draw and adequate cooling.
- Electrical Input & BEC: Specified 3–8S LiPo stack power configuration, with 5V and 12V regulated outputs; check voltage, current and capacitor ratings.
- I/O & Digital FPV Integration: USB-C connection, multiple UARTs and a dedicated video-unit connection for compatible DJI digital FPV builds; confirm the exact pinout.
- Mounting & Configuration: 30.5 × 30.5mm stack mounting, suitable wiring and connector orientation; verify the GEPRC firmware target before first power-up.
